![]() ![]() Extend another piece of pipe to reach from the 45° elbow to the “Y” connector on the other pipe.Ĭonnections securely to prevent leaking, and tighten all the hose clamps. Under the pump if there are rocks or other debris on the sump floor that may clog the pump.Ībove the check valve of the Pro Series pump, and attach a 45° elbow to that pipe. Do not mount the pump to any existing pipes it should be placed on the floor of the sump. On the bottom of the sump floor next to the main AC pump. Place the pump with the PVC pipe attachment in the event of power failure, you could install a back-up battery for your sump pump. Attach the wire to the pipe with a piece of tape.Ħ. All you need to know about installing a sump pump in a basement. Secure the pump wire so that the plug on theĮnd will not fall into the sump. Once the system is pressurized after a few. Once the municipal water starts flowing to the Water Commander, it will immediately start pumping water from your sump pit. Once your install is complete, open the valve on your water feed to test the pump. This 12-volt battery-powered sump pump is used for (but not limited to) power outages, primary pump failures, and additional protection in conjunction with a primary pump. Now connect the bottom of the assembly to the check valve and tighten the hose clamp.ĥ. Just push the tube into the fitting, no tools are needed. Barracuda® 12-Volt Emergency Battery Back Up Sump Pump. Prime and cement the top of the “Y” assembly to the discharge pipe with the “Y” extension facing down toward the backup pump. Now prime and cement a small piece of 1½” PVC pipe to the bottom of a “Y” connector. Install a check valve on the top of the pipe and tighten the bottom hose clamp. Cut the discharge pipe approximately one (1) foot above the floor. Pipe of the main AC pump, one must be installed at this time. If there is no check valve on the discharge If a 1/8” hole is not drilled in the pipe above the pump, an air lock may prevent the pump from operating.Ĥ. ![]() Drill the hole at a 45º angle toward the bottom of the sump to avoid splashing water outside the sump pit. Make sure it is above the water line and below the check valve. Must be drilled in the PVC pipe above the Pro Series pump. Make sure it is installed with the arrow pointing up or it will not prevent the backflow of water.ģ. Install a check valve on the top of the PVC Prime and cement it to a 1½” pipe adapter, then screw the adapter into the pump.Ģ. To reach from the bottom of the sump pit to one (1) foot above the floor. Download Basementsaver Sump Pump & Backup Sump Pump Installation Manuals. Cut a piece of 1½” rigid PVC pipe long enough Failure to do so could cause serious injury or death.ġ. Unplug the main AC pump when installing the backup pump to avoid electric shock. This Old House plumbing and heating expert Richard Trethewey shows how to keep a basement dry with a battery-operated backup sump pumpeven when the power goes out. It is important to keep the discharge pipes on both pumps parallel to each other, so that the pumps remain flat on the floor of the sump. Do not cement them together until you are sure they are cut to the correct lengths. Cut the pipes and assemble them as shown in photo #7. For more help, feel free to call our customer service department at (800) 991-0466, option 3.INSTALLATION B: CONNECTION TO AN EXISTING DISCHARGE PIPE (Diagram B)ĭepending on your installation requirements, PVC pipe lengths will vary. Finding the right troubleshooting guide should be the first step when dealing with any problem you're not familiar withįind your system below to get the right download.Maintaining your equipment properly helps to prevent future problems and unwanted costs.Download the full manual or just the most helpful information for your needs. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |